Confirm that the voltage selector switch is set to V. Attach the supplied power cord to the AC power receptacle located on the rear of the printer. Connect the opposite end of the power cord to a properly grounded source of VAC 50 or 60 Hz power rated for at least 5 Amps. Depending on how the printer was ordered, a power cord may or may not be provided for VAC operation.
If not provided, obtain a cord set with the proper AC Power plug. CAUTION: To ensure that the S-Series Printer has proper ventilation and cooling, do not place any padding or cushioning material on the back of or underneath the unit because this will restrict the air flow. The S-Series Printer may be installed on any solid, level surface of sufficient size and strength to accommodate the unit.
The area in which the printer will operate must meet the environmental conditions specified. Since the Zebra S-Series Printer was designed and is fabricated as an industrial-type unit, it will function satisfactorily in areas such as a warehouse or factory floor that conform to the specified environmental and electrical conditions. Note: When placing the ribbon roll on the Ribbon Supply Spindle, make sure that the core is pushed up against the stop on the ribbon supply spindle and that the ribbon is aligned squarely with its core.
If this is not done, the ribbon may not cover the inside edge of the printhead, exposing print elements to potentially damaging contact with the media. Note: Do not load ribbon if the printer is to be used in the Direct Thermal Mode. If the printhead is not protected by the smooth backing of the ribbon, excessive abrasion may cause premature printhead failure.
Open the printhead by moving the handle to the OPEN position. Tear off a strip of media labels and backing about 6 to 12 inches long from the roll.
Peel off a label from this strip. Remove the remaining labels. Apply half of this label to the end of the strip and the other half to the end of the ribbon. This acts as a ribbon leader. Thread the leader and attached ribbon as shown in the illustration. Be careful not to crease or wrinkle the ribbon. Place the leader under the long leg of the Hook and wind for several turns.
Align the segments of the Ribbon Supply Spindle. Place the leader around the Ribbon Take-Up Spindle and wind counterclockwise for several turns. Refer to Figures 2. When the media is loaded, close the printhead by moving the lever on the upper printhead mechanism to the CLOSED position. Note: The first time you load media and whenever you subsequently change the media type you must re-calibrate the printer.
See the Configuration and Calibration Section. Roll media may contain labels of a fixed length with gaps in between or it may be formed as one continuous length with no gaps see Continuous Media in the Glossary. Both types of roll media mount inside the printer in the same manner. To load roll media, refer to Figure 2. Place the media roll on the Media Supply Hanger. The Guide must not cause pressure or excessive drag on the Media Supply Roll.
Thread the media through the printhead as shown in the illustrations. Adjust the Media Guide until it just touches the outer edge of the media without causing it to buckle. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Zebra Se User Manual Download for 1. Table of Contents Introduction Scope.
Preventive Maintenance Overview. D-1 Glossary Index. Model Designation Labels located inside the media compartment above the frame support at the rear of the S-Series Printer include both the serial number and model designation. The microprocessor interprets this information and controls the S-Series Printer me- chanics, printhead, communications, command interpretation, label formatting, media control, and mechanical drive.
Print Mechanism Capabilities The print mechanism has been designed to print random information labels, tickets, and tags. Media Transport Mechanism Capabilities The media transport mechanism of the S-Series Printer has been designed to accommodate various types of media, including die-cut labels, ticket and tag stock, continuous roll, and fanfold media. Printer Specifications Printing Considerations Specification Se S Resolution thermal transfer dots per inch Optional Optional dots per or direct thermal 8 dots per mm dots per inch dots per inch inch 8 dots 6 dots per mm 12 dots per mm per mm Dot size 0.
Label length Tear-Off 0. Full media width. Minimum 0. Inches Height Width 0. Millimeters Height Width Char. Inspection Inspect the printer for possible damage incurred during shipment. Storage and Reshipping If you are not placing the printer into operation immediately, repackage it using the original packing materials.
Using a small flatblade screwdriver or similar tool, move the Voltage Selection switch to the V or V position as required. Figure 2. Site Requirements CAUTION: To ensure that the S-Series Printer has proper ventilation and cooling, do not place any padding or cushioning material on the back of or underneath the unit because this will restrict the air flow.
Ribbon Loading Se Refer to Figure 2. Ribbon Loading S Refer to Figure 2. Roll Media Roll media may contain labels of a fixed length with gaps in between or it may be formed as one continuous length with no gaps see Continuous Media in the Glossary.
You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Set your language preference 3. Set Asset Type to Manual All three steps are required. Asset Type -No Selection- Manual. Open a Case. Search Knowledge Base. Discussion Forum. Warranty Lookup. Product Warranty Information. Printer Software License Reset. Manage Software Licensing excluding Printers.
Device Diagnostic Tool for Mobile Devices. Find a Zebra Partner. Contact Support. Mobile Computers. Barcode Scanners. Interactive Kiosks. Operation of this equipment in a residential area is likely to cause harmful interference in which. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the. Zebra Technologies Corporation takes steps to assure that its published Engineering specifications and Manuals are correct;.
Zebra Technologies Corporation reserves the right to correct any such errors and disclaims li-. No Liability for Consequential Damage. In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production or delivery of the. Because some states do not allow the exclusion or limitation. The copyrights in this manual and the label printer described therein are owned by Zebra Technologies Corporation.
0コメント