Manufactured under license from Dolby Laboratories. All Rights Reserved. All rights reserved. Sony Corporation hereby grants the user a non-exclusive, non-transferable, limited right of use to this product under USA and foreign patent, patent pending and other technology or trademarks owned by Neural Audio Corporation and. THX Ltd. All other trademarks and registered trademarks are of their respective holders.
Other trademarks and trade names are those of their respective owners. Depending on the sound field settings and the source, there may be no sound output. Sensitivity: 2. Voltage mV Impedance: 1 kohm. Voltage: 2 V Impedance: 1 kohm. Disassembly Flow Front Panel Block Heat Sink Block Printed Wiring Board. Never reuse a disconnected chip component. Connection of the playback component and Maximum number of channels Page Using Multi-Zone Features 3.
When using an IR repeater not supplied , you can operate both a component in the main zone and Sony receiver in zone 2 or zone 3 from zone 2 or zone 3. To operate the receiver from zone 2 or zone Use Category 5e or Category 6 cable. If you want to use them in zone 3, switch the zone setting of the remote. When an IR repeater is not connected, use this receiver in the main zone. Press ZONE. The remote switches to zone 3.
Change the zone setting of the remote to zone 3 in advance page To exit the party mode Select other input in zone 2 or zone 3. Page Switching Between Digital And Analog Audio Switching between digital and analog audio When you connect components to both digital and analog audio input jacks on the receiver, you can fix the audio input mode to either of them, or switch from one to the other, depending on the type of material you intend to watch.
Page Using The Sleep Timer Using the sleep timer You can set the receiver to turn off automatically at a specified time. Page Enjoying The Surround Effect At Low Volume Levels Enjoying the surround effect at low volume levels This function allows you to retain a theater like environment at low volume levels. This function can be used with other sound fields.
When watching a movie late at night, you will be able to hear the dialog clearly even at a low volume level. Refer to the operating instructions supplied with your recording component.
Recording onto a MiniDisc or audio tape You can record onto a MiniDisc or audio tape using the receiver. Switch the command mode from the initial setting to the appropriate setting, if other Sony component is operated accidentally by the same remote, when you are operating the receiver using the remote supplied with the receiver. Page Adjusting Settings Adjusting Settings Using the setting menu You can adjust the various settings for speakers, surround effects, multi zone, etc. Setting menu list Menu icon Description Auto Sets the speaker level or Calibration distance and makes the measurement automatically page Speaker Sets the speaker position and impedance manually page Page Makes the measurement of frequency from each speaker flat.
Page Speaker Settings Speaker settings You can adjust each speaker manually. You can also adjust the speaker levels after the auto calibration is completed. Page from adjacent speakers. Some items may not be displayed, depending on the setting of the speaker pattern. Surround settings You can adjust the sound effect on the Sound Field Setup screen. A source recorded in 2 channel format is decoded into 5. Page Night Mode Dual Mono Digital broadcast language selection Lets you select the language you want to listen to during a digital broadcast.
This feature only functions for Dolby Digital sources. Page Video Settings Video settings Makes settings for video. Resolution Converting video signals Lets you convert the resolution of analog video input signals.
Stream information about the H. Page Quick Click Settings Quick Click settings Controls components connected to the receiver using the on-screen remote. Source Component Selects the source component that is to be operated. Page Menu list in the display window The following options are available in each menu.
Page Using The Remote You can control Sony or non-Sony components you are using with the remote supplied with the receiver. The remote is initially set to control Sony components. When you change the settings of the remote according to the components you are using, Main remote Page Use the numeric codes in the tables below to control non-Sony components and also Sony components that the remote is normally unable to control.
Since the remote signal that a You can specify up to 20 commands for each macro list. Page Other Components Press the buttons you want to program in the same sequence as you want the operation s to be performed. Page Setting Remote Commander Codes That Are Not Stored In The Remote Setting remote commander codes that are not stored in the remote Even if a remote commander code is not one of the presets stored in the remote, it is possible for the remote to learn the code using the learning function.
Note When setting up the receiver to learn the remote command modes, replace the batteries with new Page Using On-Screen Remote Quick Click Using On-screen Remote Quick Click Operating components or lighting connected to the receiver using the on screen remote Quick Click You can control components connected to the receiver, a projector, and the light control unit using the on-screen remote on the TV screen. Page Preparing Quick Click After referring to the operating instructions of the components connected to the receiver make sure to place the IR Blaster just above or below the remote sensor.
Remote sensors on Sony Recorders and other products are identified by the symbol. Note Do not remove the backing paper from the IR Blaster yet. The following explanation provides examples of normal operation.
The component may work differently, or may not work at all depending on the component. Page 10 key tab Button Function Select to turn components connected to the receiver on or off. Select to turn components connected to the receiver on or off.
Then press the selection. E Menu Select to display the menu of components connected to the receiver. Size Note: When this confi rmation is executed, IP address is changed. Category 5 cable, normal type or shield type. Multifunction remote commander. Connection: The router need not be connected with the internet.
Procedure: 1. It changes to the setting that displays the image in the monitor.
0コメント